MPE
MPE Limited
Hammond Road,
Knowsley Industrial Park, Liverpool
L33 7UL
Contact
T: +44 (0)151 632 9100
F: +44 (0)151 632 9112
E: sales@mpe.co.uk

Standard Performance EMC Filter Range

Download

Please enter your email address below to download.

MPE Standard Performance Installation Filter A

 

 

 

 

 

 

 

 

From screened rooms to industrial power equipment, uncontrolled radio interference presents a common hazard. This range of filters is designed specifically for use on single and three phase mains, and has all the advantages of using current compensating inductors.

All MPE installation filters are tested using the test methods defined within the following standards and meet or exceed the relevant performance and/or safety criteria defined within these standards:

Mil-F-15733
Mil-Std-220C
CISPR17:2011/BS EN 55017:2011
UL1283
EN60950/IEC60950

GENERAL SPECIFICATION

Rated Voltage
Single Phase Filters
250V a.c. 50/60Hz (also suitable for 2 line d.c. supplies up to 600V d.c. provided that load current returns through the filter)
Three Phase Filters
250/440V a.c. 50/60Hz
Rated Current
As tabulated
Insertion Loss
See graph and table
Performance curve 1 meets 100dB at 10kHz
Performance curve 2 meets 100dB at 50kHz
Maximum Temperature Rise on Full Load
25°C
Operating Temperature Range on Full Load
-45°C to +50°C
Maximum Full Load Heat Dissipation
As tabulated
Maximum Volt Drop per line at Full Load d.c. Current
As tabulated
Discharge time to below 34V
30s maximum

RANGE AVAILABLE

Current Rating (A) MPE Part Number Performance Curve Volt Drop (mV) Heat Dissipation (W) Major Dimensions (mm) Case Size (see Installation Details Page Installation Details) Approx Weight (kg)
A B C
Single Phase (+N)
6 DS23547 1 500 7 310 175 90 a 8
10 DS23330 1 500 11 310 175 90 a 8
16 DS23752 1 500 14 310 175 90 a 8
32 DS23332 1 500 22 550 205 95 e 16
63 DS23334 1 500 50 550 205 105 f 20
100 DS23336 2 500 60 640 205 120 i 22
200 DS23708 2 500 120 660 475 135 u 60
400 DS26050 2 500 150 1250 475 150 mm 110
Three Phase (+N)
6 DS23619 2 500 11 310 350 90 b 16
10 DS23331 2 500 16 310 350 90 b 16
32 DS23333 1 500 45 550 410 95 g 22
63 DS23335 2 500 70 550 410 110 h 32
100 DS23337 2 500 70 660 410 135 j 45
200 DS23709 2 500 160 660 575 150 v 70
400 DS26051 2 500 170 1250 575 150 nn 120

APPLICABLE NATO STOCK NUMBERS (NSN)

MPE Part Code Description NSN
DS23547 6A Single Phase 5915-99-310-0769
DS23330 10A Single Phase 5820-99-310-8911
DS23752 16A Single Phase 5915-99-968-7487
DS23332 32A Single Phase 5915-99-176-8426
DS23334 63A Single Phase 5915-99-152-3079
DS23336 100A Single Phase 5915-99-391-4527
DS23708 200A Single Phase 5915-99-156-5318
DS26050 400A Single Phase 5915-99-847-7146
DS23619 6A Three Phase 5915-99-291-1718
DS23331 10A Three Phase 5915-99-377-6256
DS23333 32A Three Phase 5820-99-570-1166
DS23335 63A Three Phase 5915-99-371-3551
DS23337 100A Three Phase 5915-99-671-1575
DS23709 200A Three Phase 5915-99-959-4382
DS30929 250A Three Phase 5915-99-918-6144
DS26051 400A Three Phase 5915-99-845-4990

TRANSIENT SUPPRESSION

All types can be supplied with integral transient suppression fitted between each input terminal and earth.

Varistor rating: 275V a.c. 140 Joules (10/1000μs)

Other varistor ratings can also be supplied. To specify the transient suppressed version, suffix V is added to the filter part number (see ordering code).

TYPICAL INSTALLATION DETAILS

The standard cable entry consists of an end conduit entry hole on the filter input (supply) side and a base conduit exit hole on the output (load) side.

Filters can be supplied with other cable entry positions if required upon request. Please refer to Installation Details page.

To facilitate installation of these filters, separate fixing kits are available to suit bulkhead panel thicknesses up to 20mm. Please refer to fixing kits product page.

ORDERING CODE

DS XXXXX / X / X e.g. DS23330CV

Filter Part Number

Suffix C for standard cable entry
For other cable entries, see Installation Details page

Add suffix V for transient suppressed filter