MPE
MPE Limited
Hammond Road,
Knowsley Industrial Park, Liverpool
L33 7UL
Contact
T: +44 (0)151 632 9100
F: +44 (0)151 632 9112
E: sales@mpe.co.uk

Standard Performance HEMP & IEMI Filter Range

Download

Please enter your email address below to download.

MPE HEMP Prot Standard Performance A

 

 

 

 

 

 

 

 

 

DESCRIPTION

A range of 2 line and 4 line (single & three phase) Power Line HEMP filters independently tested and certified as meeting and exceeding the pci requirements of Mil-Std- 188-125-1 and -2 and Def Stan 59-188 parts 1 and 2 for E1 and E2 pulses. All lines are individually filtered and feature inductive input to offer both good continuous wave EMC performance and superior transient handling performance even on supplies with low source impedance. All lines are fitted with high-energy transient suppressors.

All MPE HEMP filters are tested using the test methods defined within the following standards and meet or exceed the relevant performance and/or safety criteria defined within these standards:

Mil-Std-188-125
Mil-F-15733
Mil-Std-220C
CISPR17:2011/BS EN 55017:2011
UL1283
EN60950/IEC60950
USACE 13.27.54.01.
UFGS 13.49.20.01.

FEATURES

  • 250V/440Vac with 6A – 1200A current ratings
  • 2 or 4 individually filtered lines
  • Utilise MPE self-healing feedthrough capacitors
  • Significantly smaller & lighter than traditional solutions
  • Much lower heat dissipation than traditional solutions
  • High energy transient suppressors for high reliability
  • UL94-V0 insulating materials used
  • Complies with IEC 950 requirements
  • Very low residual pulse current – high safety margin

RATINGS & CHARACTERISTICS

Rated Voltage (All Filters) 250Vac 50/60Hz or 300V dc each line to case
Rated Voltage (4 line 3 phase filters) 250/440Vac 50/60Hz (277V/480Vac on request)
Test Voltage 2250Vdc each line to case (Prior to fitting   transient suppressors)
Insulation Resistance >100MΩ (Prior to fitting discharge resistors)
Discharge Resistors Fitted internally from each line to case
Discharge Time to below 34V <30s
Maximum Temperature Rise on Full Load 25ºC
Full Load Operating Temperature Range -40ºC to +50ºC
Maximum Leakage Current per line at 250Vac 50Hz See table
Peak Surge Current 70kA (8/20μs)

INSERTION LOSS PERFORMANCE

Minimum insertion loss In 50Ω system with / without load
Frequency 10kHz 100kHz 1MHz 10MHz 100MHz 1GHz
Insertion loss 20dB 40dB 60dB 80dB 80dB 80dB

TRANSIENT SUPPRESSION PERFORMANCE

MIL STD 188-125-1 acceptance test, short pulse current injection, wave shape 20/500ns
Input pulse amplitude 250A 500A 1000A 1800A 2500A
MIL-STD-188-125 residual requirement <10A <10A <10A <10A <10A
Typical filter residual let-through <1.5A <2A <3A <3.5A <4.5A

 PRODUCT RANGE

Part Number Current Rating (A) @50ºC No of Lines Max Leakage Current per Line (A) Max DC Volt Drop per Line (V) Max Heat Dissipation (W) Major Dimensions (mm) Weight(Kg)
Length Width Depth
DS33330 6 2 1.5 0.1 5 420 200 120 10
DS33331 16 2 1.5 0.2 10 420 200 120 10
DS33332 32 2 1.5 0.2 20 500 250 120 14
DS33333 63 2 1.5 0.3 40 620 320 170 30
DS33334 100 2 5 0.2 65 740 350 230 40
DS33335 200 2 5 0.1 80 860 450 250 70
DS33336** 400 2 8 0.1 130 1600 480 250 120
DS33340 6 4 1.5 0.1 10 420 400 120 20
DS33341 16 4 1.5 0.2 20 420 400 120 20
DS33342 32 4 1.5 0.2 40 500 500 120 30
DS33343 63 4 1.5 0.3 75 620 640 170 55
DS33344 100 4 5 0.2 125 740 700 230 80
DS33345 200 4 5 0.1 140 860 900 250 130
DS33346** 400 4 8 0.1 250 1600 960 250 225

*Current derating between 50ºC and 85ºC Iθ = IR

DIMENSIONS & MECHANICAL DETAILS

Part Number Dimensions (mm)
A B C D E F G H J K L M N
DS33330 420 200 120 340 110 45 40 140 80 20 9 M5 M6
DS33331 420 200 120 340 110 45 40 140 80 20 9 M5 M6
DS33332 500 250 120 410 140 55 45 160 100 25 9 M8 M10
DS33333 620 320 170 530 210 55 45 160 100 32 11 M8 M10
DS33334 740 350 230 630 240 55 55 160 120 32 11 M8 M10
DS33335 860 450 250 710 300 75 75 200 150 51 17 M12 M16
DS33336** 1600 480 250 1140† 340 70 230 300 300 76 17 M20 M20
DS33340 420 400 120 340 310 45 40 140 80 20 9 M5 M6
DS33341 420 400 120 340 310 45 40 140 80 20 9 M5 M6
DS33342 500 500 120 410 390 55 45 160 100 25 9 M8 M10
DS33343 620 640 170 530 530 55 45 160 100 32 11 M8 M10
DS33344 740 700 230 630 590 55 55 160 120 32 11 M8 M10
DS33345 860 900 250 710 750 75 75 200 150 51 17 M12 M16
DS33346** 1600 960 250 1140† 600 180 230 300 300 76 17 M20 M20

** 400A filters additionally have lifting lugs protruding 65mm beyond each end of the filter and 8mm beyond each side to
aid mounting. Lug hole size 22mm. Please request drawings P828749 or P828750 for full dimensions of 2 line and 4 line 400A filters
respectively.

† Fixing centres only See drawing P828602 or P828362 for position of cable entry hole.